R1.0
05.03.2004 |
-
First principle protocol implementation
|
R2.0
(14.03.2004)
|
Optimised initialisation while
power-on
Optimised timing
Reading of HU keys
|
R2.1
(20.03.2004)
|
-
Complete protocol implementation
-
Optimisation for target controller
-
RAM/ROM ressources optimisation
-
Archos remote control
-
Debug interface via RS232
-
Further optimised initialisation
while power-on
-
More fault free recognition of
HU keys
-
HU key press is now displayed
with a short blink of 'Track 01'
|
R2.2
(25.07.2004)
|
-
All 6 Archos functions are now
additionally available on CD1-6 keys (VW) and 1-6 (Audi)
-
Evaluation of CDC Power Control
signal during power on and off
-
Bugfix: Archos player was not
powering up correctly, due to wrong pin initialisation.
-
Several bugfixes for versions
without Archos remote control
-
Full simulation of time display
from 00:00 to 59:59
-
Only MCD: The CD number is now
toggling between ':' and 'blank' to show availability of the CDC signal
-
Improvement in radio initialisation,
so VW MFD is now working too with the CDC simulator
-
Changing mode from CDC to radio
(or pressing MUTE) is now switching the Archos player to pause mode.
Changing back mode from radio
to CDC (or pressing MUTE again) makes the Player continuing to play.
In parallel Pin9 is supported
(details please see Comment
according to Archos Power Control during pause).
-
Different kyboard layouts for
MCD, MFD and Audi radios
-
Adaption for Audi Concert II radio
|
R2.3
(20.10.2005)
|
-
New implementations:
-
VW Beta V, Gamma V radios
-
VW BetaIV, Gamma IV radio
-
VW New Beetle radio
-
VW RN-S2 navigation system
-
VW RCD300 radio
-
Audi Navi Plus navigation system
-
Audi Chorus II radio
-
Audi Concert I radio
-
Audi Symphony I radio
-
Skoda Symphony radio
-
Seat Aura V3 radio
-
"Stand-Alone" version (later renamed
to "CDC-Emu Car-PC")
-
More stable recognition of radio
key presses
-
Only VW radios: SCAN key is now
evaluated and plays each song for 10s until key is pressed again
-
Only Audi radios: Re-initialisation
of the radio after communication fault.
-
Adaption to changed initialisation
procedure of newer VAG radios and navigation systems.
-
Further RAM/ROM ressources optimisation.
-
SW version can now be read out
via serial interface.
-
Optimised key layouts for operation
with multi-functional steering wheel (steering wheel remote), for:
-
VW Beta V, Gamma V radios
-
VW MCD navigation system
-
Audi Navi Plus navigation system
-
Changed feedback to radio in case
CDC mode is exited (more stable "log-out" out of CDC mode).
-
Only "Car-PC" version (since R2.3.12):
It's now possible to modify the radio display (CD#, track#, min., sec.)
via serial commands to the CDC-Emu.
-
More stable behaviour while changing
between CDC mode and radio mode.
-
SymphonyII: "Hang-Up" while selecting
CDC mode solved.
-
SymphonyII: "Hang-Up" while pressing
the '<' key (if time info is <5s) solved.
-
SymphonyII: Track-Selection-Wheel
is now supported.
-
SymphonyII: SCAN mode implemented.
-
SymphonyII: Can now be used in
the versions "CDC-Emu AJB" and "CDC-Emu Car-PC" without restrictions.
-
Bugfix: In SCAN mode the next
track was selected after 9s instead of 10s.
-
Concert I (only Panasonic): CDC
Simulator is now also recognised if you switch back from cassette to CDC
mode.
|
R2.4
(on-going)
|
-
Conversion to Atmel ATtiny2313-20
(Atmel AT90S2313-10 not available anymore). Software is fully compatible
with HW V1.3.
-
No more support for Audi Concert
I radio (due to few demands).
|